Axles

Rear axle shaft. LR

Left rear axle shaft Fits: Willys MB (1941-1945) w/ Dana 27 Rear Axle; 10 Splines; 30-5/8″ Long; Rear Left.

Rear axle shaft, RR

Right rear axle shaft Fits: Willys MB (1941-1945) w/ Dana 27 Rear Axle; 10 Splines; 22″ Long; Rear Right.

Ring gear bolt locking strap

Ring gear bolt locking plate Fits: Willys MB (1941-1945) w/ Dana 25 Front Axle. Willys MB (1941-1945) w/ Dana 27 Rear Axle. Willys M38 (1950-1952) w/ Dana 25 Front Axle. Willys M38-A1 (1952-1963) w/ Dana 25 Front Axle. Jeep...

Kinpin stud, Dana 25/27

King pin stud, 16 needed to rplace all weak bolts   Fits: Jeep CJ-2A (1945-1949) w/ Dana 25 Front Axle. Jeep CJ-3A (1948-1953) w/ Dana 25 Front Axle. Jeep CJ-3B (1953-1965) w/ Dana 25 Front Axle. Jeep CJ-3B (1966-1968) w/...

Pinion inner race, Dana 25F/27R/44R

Pinion inner race.   Fits Jeep: Jeep Wrangler (YJ) (1987-1995) w/ Dana 44 Rear Axle. Jeep Cherokee (XJ) (1986-1990) w/ Dana 44 Rear Axle. Jeep Comanche (MJ) (1986-1992) w/ Dana 44 Rear Axle. Fits Vintage Jeep: Willys...

Drive flange, LH/RH 10 spline

Front axle drive flange. This is a must in your emergency parts box, when you explode a lock-out hub, bolt this on for full time four wheel drive.   Fits: Willys MB (1941-1945) w/ Dana 25 Front Axle. Willys M38 (1950-1952) w/ Dana 25...

Wheel bearing bearing, for bearing marked 18590 (#52943)

Wheel bearing Fits: Willys MB (1941-1945) w/ Dana 25 Front Axle; w/ Dana 27 Rear Axle. Willys M38 (1950-1952). Willys M38-A1 (1952-1963). Jeep CJ-2A (1945-1949) w/ Dana 25 Front Axle. Jeep CJ-3A (1948-1953) w/ Dana 25...

Wheel bearing race for bearing marked 18591 (#52942)

Wheel bearing race Fits: Willys MB (1941-1945); Front. Willys MB (1941-1945) w/ Dana 27 Rear Axle; Rear. Willys M38 (1950-1952); Front. Willys M38-A1 (1952-1963); Front. Jeep CJ-2A (1945-1949); Front. Jeep...

Warn lockout hub service kit, M54/M19

Driving off-road is what weekend thrill seekers live for, but over time it causes even the best automotive parts to wear. Warn service kits provide the correct parts for maintaining their locking hubs and getting your vehicle back on the trails...

Hub gasket, early scalloped outside

Hub gasket for early Dana 25/27 with scalloped outside edges

Pinion nut washer and F/R output yoke washer

Pinion nut washer/Axle shaft nut to hub washer Fits Jeep: Jeep Wrangler (TJ) (1997-2006) without Rubicon Package; w/ Dana 30 Front Axle or Dana 44 Rear Axle. Jeep Wrangler (TJ) (1987-1995); Front Axle. Jeep Wrangler (TJ) (1987-1995);...

Carrier bearing shims, Dana 25/27 for new set ups

Fits: Willys MB (1941-1945) w/ Dana 25 Front Axle. Willys MB (1941-1945) w/ Dana 27 Rear Axle. Willys MB (1941-1945) w/ Dana 27 Rear Axle. Willys M38 (1950-1952) w/ Dana 25 Front Axle. Willys M38-A1 (1952-1963) w/ Dana 25...