1981-85 JEEP CJ8 SCRAMBLER

Dana 18/20 1-1/4" intermediate shaft kit

1-1/4" intermediate shaft roller bearing/thrust washer kit   Fits: Jeep CJ-3B (1953-1968) w/ Dana 18 Transfer Case; w/ 1-1/4″ Intermediate Shaft. Jeep CJ-5 (1955-1971) w/ Dana 18 Transfer Case. Jeep CJ-5 (1972-1979) w/...

Spring plate, 2" wide front spring, RF

Fits: Jeep CJ-5 (1976-1983) Jeep CJ-7 (1976-1986) Jeep CJ-8 (1981-1986) Jeep Commando (1972-1973) You can either leave the stabilizer stud or cut it off   RF 2" Leaf Spring Plate; Includes Stabilizer Link Stud. Dana 30

Clutch alignment tool

Clutch alignment tool, 9/16" pilot, 1-1/8" 10 spline   Fits Jeep: Jeep Wrangler (YJ) (1991) w/ 4.0L engine. Jeep Wrangler (YJ) (1987-1990) w/ 4.2L engine. Jeep Cherokee (XJ) (1987-1991) w/ 4.0L engine. Fits Vintage...

Brake hose pair for disc brakes, stainless steel, 7/16" banjo

Braided Stainless Steel Brake Hose 7/16 Diameter  Banjo bolts & crush washers included 18" long Set of 2 3/8-24 IFF fitting to hard line.

Brake calipers, loaded for caliper mounts CB7191

GM 7" Large Single Piston Caliper Set Pre Loaded with pads Caliper Pins Included Cast Iron Finish Sold as a set Left (4045) & Right (4046) Single Piston Uses 7/16-20 banjo bolts, not included 1974-1978 Jeep Cherokee, Wagoneer, J10,...

Dana 25/27/30/44/53 outer pinion bearing

Timken outer pinion bearing for Dana 25/27/30/44/53. Bearing only   Fits Jeep: Jeep Wrangler (TJ) (1997-2006) w/ Dana 44 Front or Dana 44 Rear Axle. Jeep Wrangler (YJ) (1987-1995) w/ Dana 30 Front or Dana 44 Rear Axle. Jeep Cherokee...

Dana 25/27/30/44/53 outer pinion bearing race

Timken Pinion bearing race, Dana 25/27/30/44/53 Fits Jeep: Jeep Wrangler (TJ) (1997-2006) w/ Dana 44 Front or Dana 44 Rear Axle. Jeep Wrangler (YJ) (1987-1995) w/ Dana 30 Front or Dana 44 Rear Axle. Jeep Cherokee (XJ) (1984-1999) w/...

Steering stabilizer kit

Steering stabilizer kit Multiple mounting options for manual or power steering.

Fuel sending unit filter, in tank filter

Fuel filter for the end of the fuel sending unit. #4.134-1 in diagram.   Fits: Jeep CJ (1972-1986) Jeep Commando (1972-1973)

U Bolt set for driveline u-joint

U Bolt kit for driveline u-joints The kit does one u-joint (one end of drive shaft)

Snaps, male stainless steel with #8 sheet metal screw stud, each

Stainless steel male stud snap, #8 sheet metal stud.

Spindle bushing, Dana 25/27/30

Inner spindle bushing   Fits: Willys MB (1941-1945) w/ Dana 25 Front Axle. Willys M38 (1950-1952) w/ Dana 25 Front Axle. Willys M38-A1 (1952-1963) w/ Dana 25 Front Axle. Jeep CJ-2A (1945-1949) w/ Dana 25 Front Axle. Jeep...