Axles

U bolt, front and rear (not the large front one)

U bolt for front and rear ends. This is the one that goes over the axle tube, not over the front differential housing (#808988). Come with nuts and washers. You need 7 total,  3 for the front and 4 for the rear to complete replacement (and 1...

Ball joint kit, Dana 30/44, one side

Ball joint kit for open knuckle Dana 30 front end. Both upper and lower ball joints with all the hardware to replace the ball joints. This kit does one side.  Black boots (blue shown in picture is just shipping protector for the...

Spring Shackle Front 2"

Front Spring shackle for Jeepster with 2" front Springs. Please measure before ordering, as this was a late change in '70-'71 through '73 for the Jeepster. Fits: Jeep CJ (1976-1986); Front. Jeepster (Late 70-71 to 73) Please measure spring

U Joint for Spicer driveshaft

Fits:Jeep CJ-3B (1953-1968) w/ Spicer Driveshaft; w/ 2.438″ Wide U-Joint.Jeep CJ-5 (1955-1971) w/ Spicer Driveshaft; w/ 2.438″ Wide U-Joint.Jeep CJ-6 (1955-1971) w/ Spicer Driveshaft; w/ 2.438″ Wide U-Joint.Jeep C101...

Pinion oil seal

This Part Fits The Following: Fits Jeep: Jeep Wrangler (YJ) (1987-1993); Front Axle. Jeep Cherokee (XJ) (1984-1986); Front Axle; w/ Dust Slinger on Yoke. Jeep Cherokee (XJ) (1986-1992) w/ Dana 44 Rear Axle; w/ Std Differential. Jeep...

Tie Rod Clamp

Tie rod clamp. Inner or Outer Tie Rod Clamp for Left or Right Tie Rod Assembly; Includes Clamp and Hardware    Fits: Willys MB (1941-1945). Willys M38 (1950-1952). Willys M38-A1 (1952-1963). Jeep CJ-2A (1945-1949). Jeep CJ-3A...

Front hub bearing cup

Inner and outer front bearing cup.  Fits all Dana 27 and Dana 30 axles.

Lug stud, Dana 44 rear flanged axle

Rear axle lug stud.  Fits Dana 44 rear flanged axles.  Fits 71/71 Jeepster Commando.  Also fits: Jeep CJ (1976-1986) with Model 20 Rear Axle. Jeep CJ (1986) with Model 44 Rear Axle.  

Axle bearing kit for Dana 44 flanged

Dana 44 rear flanged outer bearing kit.  Includes 18, 19, 20, 21, & 22 in the diagram.

Lug Stud 1/2-20, C101 tapered rear

  Front Hub Stud; Right Hand Threads: Fits: Willys M38 (1950-1952). Willys M38-A1 (1952-1963). Jeep CJ-3A (1948-1953). Jeep CJ-3B (1953-1968) w/ Bearing Marked 18590. Jeep CJ-5 (1955-1965) w/ Bearing Marked 18590...

Lug stud, flanged axle

   Fits: Jeep CJ-5 (1976-1983) w/ AMC 20 Rear Axle. Jeep CJ-7 (1976-1986) w/ AMC 20 Rear Axle. Jeep CJ-8 (1981-1986) w/ AMC 20 Rear Axle. Jeep CJ-7 (1986) w/ Dana 44 Rear Axle. Jeep CJ-8 (1986) w/ Dana 44 Rear...

Differential cover gasket, Dana 44

Differential cover gasket, fits all Dana 44 axle covers.  Number 10 in the diagram