Axles

Pinion oil seal gasket, Dana 25/27/44

Pinion oil seal gasket, Dana 25/27/44 This goes in before you install the seal and seals the seal to the axle housing

U-Bolt HD multi leaf 1/2" x 7"

Fits: Willys M38-A1 (1952-1963) w/ Dana 44 Rear Axle. Jeep CJ-3A (1948-1953) w/ Dana 44 Rear Axle. Jeep CJ-3B (1953-1968) w/ Dana 44 Rear Axle. Jeep CJ-5 (1955-1975) w/ Dana 44 Rear Axle. Jeep CJ-6 (1955-1975) w/ Dana 44...

Lockout hubs, 10 spline

Lock out Hubs. Don't have all that drive train turning on the highway, turn out your hubs and freewheel!! Save wear and tear and get better mileage.   6 bolt, 10 spline   Fits: 67-71 Jeepster Commando 1948-1950 Jeep Jeepster 1963-1973...

Pinion yoke, Dana 25/27/44 10 spline 1310 u-joint

Dana 25/27/44 rear yoke. 10 spline, u bolt style 1310 u joint. Stock for 67-71 Jeepster Commando w/ Dana 44. Stop those leaks with a new yoke!   Fits: Willys MB (1941-1945) w/ Dana 25 Front Axle. Willys MB (1941-1945) w/ Dana 27 Rear...

U Bolt, Front large one

Front end large u bolt that goes over front differential housing. Need one per vehicle.   Fits: Willys MB (1941-1945). Jeep CJ-2A (1945-1949). Jeep CJ-3A (1948-1953). Jeep CJ-3B (1953-1968). Jeep CJ-5 (1955-1975)...

U bolt, front and rear (not the large front one)

U bolt for front and rear ends. This is the one that goes over the axle tube, not over the front differential housing (#808988). Come with nuts and washers. You need 7 total,  3 for the front and 4 for the rear to complete replacement (and 1...

Ball joint kit, Dana 30/44, one side

Ball joint kit for open knuckle Dana 30 front end. Both upper and lower ball joints with all the hardware to replace the ball joints. This kit does one side.  Black boots (blue shown in picture is just shipping protector for the...

Spring Shackle Front 2"

Front Spring shackle for Jeepster with 2" front Springs. Please measure before ordering, as this was a late change in '70-'71 through '73 for the Jeepster. Fits: Jeep CJ (1976-1986); Front. Jeepster (Late 70-71 to 73) Please measure spring

Dana 25/27 knuckle seal kit, both sides

Fits: Willys MB (1941-1945) w/ Dana 25 Front Axle. Willys M38 (1950-1952) w/ Dana 25 Front Axle. Willys M38-A1 (1952-1963) w/ Dana 25 Front Axle. Jeep CJ-2A (1945-1949) w/ Dana 25 Front Axle. Jeep CJ-3A (1948-1953) w/ Dana...

Wheel stud (front)

Fits: Jeep CJ-5 (1976-1983) w/ Front Disc Brakes. Jeep CJ-7 (1976-1986) w/ Front Disc Brakes. Jeep CJ-8 (1981-1986) 

Bearing Cup (Outer Pinion)

Bearing cup (outer pinion) Fits Jeep: Jeep CJ (1980-1986) w/ Dana 300 Transfer Case. Jeep C101 Commando (1966-1971) w/ Dana 30 Rear Axle.

U Joint for Spicer driveshaft

Fits:Jeep CJ-3B (1953-1968) w/ Spicer Driveshaft; w/ 2.438″ Wide U-Joint.Jeep CJ-5 (1955-1971) w/ Spicer Driveshaft; w/ 2.438″ Wide U-Joint.Jeep CJ-6 (1955-1971) w/ Spicer Driveshaft; w/ 2.438″ Wide U-Joint.Jeep C101...