Body

Front rocker panel to floor body mount, LH/RH 1966-73 Jeepster/Commando

Front rocker panel to floor body mount,  LH/RH 1966-73 Jeepster/Commando New reproduction front frame braces will fit driver and passenger side. Main frame braces are located under the front floor section andwelds to inner rocker panel. These...

Door entry step replacement panel, 1966-73 Jeepster/Commando

Door entry step replacement panel, 1966-73 Jeepster/Commando   New reproduction door step fits driver and passenger side, but sold separately. Fits bottom door entry flat area. The top portion of door will attach to front floor pan and the...

Rear floor rear hat channel section with body mount captured nuts, 66-73 Jeepster/Commando

Rear floor rear hat channel section with body mount captured nuts, 66-73 Jeepster/Commando This is the bed hat channel right over the rear crossmember This is the steel piece for the rear of the body. This has the mating hardware for the two rear body...

Front floor seat mounting brace, Jeepster/Commando, RH Front

New replacement under body seat brace is located directly under front passenger seat bolts. Braces weld to under side of floor pan. Mated hardware pre-welded for easy installation. 1 Required - This will fit driver side front and rear and passenger...

Front floor seat mounting brace, Jeepster/Commando, LH Front/LH Rear/RH Rear

Front floor seat mounting brace, Jeepster/Commando, LH Front/LH Rear/RH Rear New replacement under body seat brace is located directly under front seat bolts. Braces weld to under side of floor pan. Mated hardware pre-welded for easy installation. 3...

Bed floor front hat channel section with body mount captured nuts, 66-73 Jeepster/Commando

Rear floor front hat channel section with body mount captured nuts New replacement underbody frame to cross member brace, just above rear wheel well. Welds to bottom of body and attaches to the driver side and passenger side frame mount body brace. Made...

Inner rocker panel brace set, 1966-71 Jeepster/Commando

New replacement braces for your inner rocker panels. These are located in the rear of the inside rocker, just in front of the wheel well. Made in the USA Fits: 1967-1971 Jeepster Commando

Passenger folding seat rubber bumper kit

Jeepster/Commando passenger seat flip up/down rubber bumper. These screw to the bottom of the passenger seat bracket and keep from scratching paint and cusioning the seat as it flips down   This set of 2 does one passenger seat

Wavy washer for tailgate arms 1966-73 Jeepster/Commando

Wavy washer on 1966-73 Jeepster/Commando shouldered tailgate arm bolts and Tailgate latch on: 1976-1977 Jeep CJ7 1981-1986 Jeep CJ7 1981-1985 Jeep Scrambler

Inner rocker panel, Jeepster/Commando

Inner rocker repair panels, sold as set, left and right side. A must for your restoration to replace high rust areas. Easy weld-in replacement.  Made in the USA. Fits: 1967-1971 Jeepster Commando 1972-1973 Commando

Outer rocker panels, Jeepster/Commando

Outer rocker panels, sold in sets. Replace high rust areas with these new outer rocker panels.  Made in the USA. Fits: 1967-1971 Jeepster Commando 1972-1973 Commando Note: 1967-71 models must trim 1.75" off front edge.

Generic glass seal, Jeepster/Commando 1/2 cab rear window/Kelley hardtop side glass

Generic window glass seal. This is sold by the foot and can be used to make all kinds of glass seals Half cab rear glass or aftermarket Kelley hard top side glass come to mind. It can be cut and glued in the corners or joined in the middle...