Body

Rear floor rear hat channel section with body mount captured nuts, 66-73 Jeepster/Commando

Rear floor rear hat channel section with body mount captured nuts, 66-73 Jeepster/Commando This is the bed hat channel right over the rear crossmember This is the steel piece for the rear of the body. This has the mating hardware for the two rear body...

Front floor seat mounting brace, Jeepster/Commando, RH Front

New replacement under body seat brace is located directly under front passenger seat bolts. Braces weld to under side of floor pan. Mated hardware pre-welded for easy installation. 1 Required - This will fit driver side front and rear and passenger...

Front floor seat mounting brace, Jeepster/Commando, LH Front/LH Rear/RH Rear

Front floor seat mounting brace, Jeepster/Commando, LH Front/LH Rear/RH Rear New replacement under body seat brace is located directly under front seat bolts. Braces weld to under side of floor pan. Mated hardware pre-welded for easy installation. 3...

Bed floor front hat channel section with body mount captured nuts, 66-73 Jeepster/Commando

Rear floor front hat channel section with body mount captured nuts New replacement underbody frame to cross member brace, just above rear wheel well. Welds to bottom of body and attaches to the driver side and passenger side frame mount body brace. Made...

Wavy washer for tailgate arms 1966-73 Jeepster/Commando

Wavy washer on 1966-73 Jeepster/Commando shouldered tailgate arm bolts and Tailgate latch on: 1976-1977 Jeep CJ7 1981-1986 Jeep CJ7 1981-1985 Jeep Scrambler

Inner rocker panel, Jeepster/Commando

Inner rocker repair panels, sold as set, left and right side. A must for your restoration to replace high rust areas. Easy weld-in replacement.  Made in the USA. Fits: 1967-1971 Jeepster Commando 1972-1973 Commando

Outer rocker panels, Jeepster/Commando

Outer rocker panels, sold in sets. Replace high rust areas with these new outer rocker panels.  Made in the USA. Fits: 1967-1971 Jeepster Commando 1972-1973 Commando Note: 1967-71 models must trim 1.75" off front edge.

Generic glass seal, Jeepster/Commando 1/2 cab rear window/Kelley hardtop side glass

Generic window glass seal. This is sold by the foot and can be used to make all kinds of glass seals Half cab rear glass or aftermarket Kelley hard top side glass come to mind. It can be cut and glued in the corners or joined in the middle...

Rear bumper with swing away tire carrier

Rear rock bumper and swing away tire carrier with welded d-ring mounts. Slanted tire mount to match the back of the Jeepster   Call for addition add-ons: 5 gallon gas rack +$150 and the tire cannot be slanted The ability to mount factory bumper...

Chrome front bumper, 1972-73Jeep Commando

Chrome front bumper New reproduction chrome front bumper. Heavy duty gauge steel finished in chrome. Note: Has 2 extra holes that can be filled with chrome round head bolts.   The length and mounting holes are exactly like the original with the...

Chrome rear bumper, 1966-73 Jeepster/Commando

Chrome rear bumper Brand new reproduction chrome rear bumper. We have finally brought these bumpers to the market to replace your bent or missing bumper. Exactly like the originals with a quality chrome plate. Fits: 1967-1971 Jeepster Commando...

Jeepster/Commando half cab rear corner seal set

Half cab rear corner seals set. FINALLY!!! some seals for the half cab!   These are the seals at the back corner of the half cab that seal to the top rail of the bed.   #25 and #26 in the diagram for both...