1946-1965 WILLYS WAGON & PANEL DELIVERY

Carter WO master rebuild kit

Master Carter Carburetor Repair Kit for Carter WOComplete with gaskets, small parts, linkage, metering rods and jets to rebuild your original Carter carburetor. Includes base gasket.Application:4-134 L engine Fits:41-45 MB41-45 GPW46-49 CJ-2A49-53...

Drive flange, LH/RH 10 spline

Front axle drive flange. This is a must in your emergency parts box, when you explode a lock-out hub, bolt this on for full time four wheel drive.   Fits: Willys MB (1941-1945) w/ Dana 25 Front Axle. Willys M38 (1950-1952) w/ Dana 25...

Dana 18 shift boot

Dana 18 shift boot Fits: Willys MB (1941-1945) w/ Dana 18 Transfer Case. Willys M38 (1950-1952) w/ Dana 18 Transfer Case. Willys M38-A1 (1952-1963) w/ Dana 18 Transfer Case. Jeep CJ-2A (1945-1949) w/ Dana 18 Transfer Case...

Wheel bearing race for bearing marked 18591 (#52942)

Wheel bearing race Fits: Willys MB (1941-1945); Front. Willys MB (1941-1945) w/ Dana 27 Rear Axle; Rear. Willys M38 (1950-1952); Front. Willys M38-A1 (1952-1963); Front. Jeep CJ-2A (1945-1949); Front. Jeep...

Fuel sender to gauge ohm converter

Finally a solution to mismatched gauges and fuel senders! This is an easy to program, inline sender ohm converter that can match any factory gauge to aftermarket sender or the other way, aftermarket gauge to factory sender.   Stop...

Warn lockout hub service kit, M54/M19

Driving off-road is what weekend thrill seekers live for, but over time it causes even the best automotive parts to wear. Warn service kits provide the correct parts for maintaining their locking hubs and getting your vehicle back on the trails...

Transfer case mount kit, Dana 18

Transfer case mount kit Fits: Willys MB (1941-1945) w/ Dana 18 Transfer Case. Willys M38 (1950-1952) w/ Dana 18 Transfer Case. Willys M38-A1 (1952-1963) w/ Dana 18 Transfer Case. Jeep CJ-2A (1945-1949) w/ Dana 18 Transfer Case...

T90 transmission Case

T90 transmission case, brand new!

Pilot bushing, F-head or L-head 134 cubic inch

Pilot bushing for F-Head or L-Head 134 cubic inch engines Fits: Willys MB (1941-1945) w/ 4-134 L-Head engine. Willys M38 (1950-1952) w/ 4-134 L-Head engine. Willys M38-A1 (1952-1963) w/ 4-134 F-Head engine. Jeep...

Clutch throw out bearing with housing, 134 CI

Clutch throwout bearing for all 134 cubic inch engines   Fits: Willys MB (1941-1945) w/ 4-134 L-Head engine. Jeep M38 (1950-1952) w/ 4-134 L-Head engine. Jeep M38A1 (1952-1963) w/ 4-134 F-Head engine. Jeep...

Intermediate shaft kit, 1-1/8"

Intermediate shaft kit Fits: Willys M38 (1950-1952) w/ Dana 18 Transfer Case. Willys M38-A1 (1952-1963) w/ Dana 18 Transfer Case. Jeep CJ-2A (1945-1949) w/ Dana 18 Transfer Case. Jeep CJ-3A (1948-1953) w/ Dana 18 Transfer Case...

Hub gasket, early scalloped outside

Hub gasket for early Dana 25/27 with scalloped outside edges